Good Times RV Parts & Accessories 2020

APPLIANCES APPLIANCES Due To Fluctuating Costs In The Market Place Such As Tariffs, Prices Are Subject To Change Without Notice, Contact Us for Latest Pricing • Special Order 253 Fan Control Igniter Board The basic purpose of a Fan Control Igniter board is to shut the fan motor off if the board fails to sense a flame after the third ignition try. Thus, battery drain is reduced and the needless blowing of cold air is eliminated. The FAN 50 Plus, after shutting the fan motor off, will wait for 1 hour and repeat the whole sequence again before permanent shut down. For 12 VDC Furnaces ONLY! The "Fan Control" feature MUST BE USED for proper operation of this board. Jumper selectable operation 12 VDC operation Works in 12 VDC furnaces* Micro controlled 3.35" x 4.25" Diagnostic LED Instructions. Three year warranty. 5-59718 FAN50PLUSPINS Ignitor Board $156.99 24 Volt Igniter Board Works in "Park Model" 110vac furnaces, which use a 24 volt AC igniter board. Includes a fuse on the board to protect the board's NC and valve circuits from short circuit damage. The LED turns red when the board activates the gas valve. For 110 VAC furnaces only. 5.10" W x 3.43" H. 3 year warranty. 5-59005 UIB 24VAC 24VAC Ingiter Board $129.49 Norcold Power Board This Dinosaur board can replace Norcold's part numbers: 621267, 621267.001, 321268, 621268.001, 621269, 621269.001, 621270, 621270.001, 619360, 619361, and 6321268.001. In an addition to being fully compatible, the no cooling fault code can be reset from operator panel. Three year warranty. 5-59212 6212XX 2 & 3-Way Norcold Board $306.49 Circuit Board Tester 12 VDC - This handy Tester plugs into a cigarette lighter. Tests most 12 VDC Ignitor boards that do not use an external sense wire. Small and easy to use, toss it in the tool box to keep it handy. 1 Year factory warranty. Easy to use: Plug the tester onto the board, Hook up the spark wire, Plug the tester into the cigarette lighter, Wait for the spark, Push the flame sense button to check the sense circuit. 5-59716 QUIKCHEK QuikChek Ignitor Board Tester $81.99 Water Heater Mounting Kit The 2-tab mounting kit allows you to mount a Dinosaur Electronic's UIB S or UIB S Post ignitor board in an Atwood ® water heater without having to drill a hole to mount the board and risk drilling a hole in the water tank. It comes with an aluminum adapter plate, a clear small cover to protect the UIB S or UIB S Post ignitor board and mounting hardware. 5-59721 2TAB 2-Tab Mounting Kit $27.49 Ignition Board Covers Covers available in small large sizes, recommended for fridge and water heaters. 5-59020 SMALL COVER Small $9.15 5-59021 LARGE COVER Large $9.15 Time Delay Relay Time delay relay is for use in older furnaces that use a standard 12VDC time delay relay. Has a 4 second delay before applying power to the fan motor, and a 2 minute cool down period at the end of the heat cycle before removing power from the fan motor. Will not operate with 110v furnaces. Specs: • 12 VDC operation • Microcontrolled • 4 second delay • 2 minute cool • down cycle • Size: 1.5" x 1.5" • Potted**NOT FOR 110VAC FURNACES.** 5-54800 48000 Time Delay Relay Switch $49.99 Ignitor Board Tester Package 12VDC ingitor board tester is able to test all 12-volt DC ignitor boards. Has bulit-in battery for on-the-go testing, will tests 75-100 boards before battery needs recharging. Tests local,remote and external flame sense. Includes: *IMT-12P Ignitor Board Tester *Dinosaur Ignitor Board Testers Video *Re-Ignitor Test Adapter *Suburban ® Fan Control Board Test Adapter *Six pin header adapter 5-59712 IMT-12PTP Ignitor Board Tester Package $283.99