SeaCoast Inc. 2021 RV Parts & Accessories

APPLIANCES APPLIANCES Special Order • Due To Fluctuating Costs In The Market Place Such As Tariffs, Prices Are Subject To Change Without Notice, Contact Us for Latest Pricing 252 UIB 24 VAC Fan Control Board For 110vac park model furnaces with fan control boards. 3 try operation. Shuts the fan motor OFF a minute and a half after the 3rd ignition try fails to sense a flame. Waits one hour and tries the cycle again before locking out requiring the thermostat to be reset. A Bi-Color LED comes on "Green" after power appears on the "AIR" terminal. The LED turns "Red" when power is applied to the valve terminal. 5-59723 24vacfanboard 24 VAC Fan Control Board $156.99 Fan Control Igniter Board The basic purpose of a Fan Control Igniter board is to shut the fan motor off if the board fails to sense a flame after the third ignition try. Thus, battery drain is reduced and the needless blowing of cold air is eliminated. The FAN 50 Plus, after shutting the fan motor off, will wait for 1 hour and repeat the whole sequence again before permanent shut down. For 12 VDC Furnaces ONLY! The "Fan Control" feature MUST BE USED for proper operation of this board. Jumper selectable operation 12 VDC operation Works in 12 VDC furnaces* Micro controlled 3.35" x 4.25" Diagnostic LED Instructions. Three year warranty. 5-59718 FAN50PLUSPINS Ignitor Board $156.99 Norcold Power Board This Dinosaur board can replace Norcold's part numbers: 621267, 621267.001, 321268, 621268.001, 621269, 621269.001, 621270, 621270.001, 619360, 619361, and 6321268.001. In an addition to being fully compatible, the no cooling fault code can be reset from operator panel. Three year warranty. 5-59212 6212XX 2 & 3-Way Norcold Board $306.49 Universal Igniter Board For Water Heaters, Furnaces, & Refrigerators The UIB Series Igniter boards are for use in furnaces, water heaters and some refrigerators. These two basic boards have spade high voltage connectors are all "3 try" boards. The replaceable fuse protects the board from short circuits LED turns red when the board activates the gas valve. The boards also have very good surge protection and tolerance to ripple voltage from "battery charger type" converters. Three year warranty. 5-59001 UIB S Ignition Board Small 4.25"x3.25" $129.49 5-59002 UIB L Ignition Board Large 5.10"x3.43" $129.49 Universal Igniter Board for Water Heaters, Furnaces & Refrigerators For water heaters, furnaces and refrigerators. The UIB Series Igniter boards are for use in furnaces, water heaters and some refrigerators. These two basic boards have or post (spark plug style top) high voltage connectors are all "3 try" boards. The replaceable fuse protects the board from short circuits LED turns red when the board activates the gas valve. The boards also have very good surge protection and tolerance to ripple voltage from "battery charger type" converters. Three year warranty. 5-59003 UIB S POST Ignition Board Small Post 4.25" x 3.25" $129.49 5-59004 UIB L POST Ignition Board Large Post 5.10" x 3.43" $129.49 24 Volt Igniter Board Works in "Park Model" 110vac furnaces, which use a 24 volt AC igniter board. Includes a fuse on the board to protect the board's NC and valve circuits from short circuit damage. The LED turns red when the board activates the gas valve. For 110 VAC furnaces only. 5.10" W x 3.43" H. 3 year warranty. 5-59005 UIB 24VAC 24VAC Ingiter Board $156.99 Ignition Board Covers Covers available in small large sizes, recommended for fridge and water heaters. 5-59020 SMALL COVER Small $9.15 5-59021 LARGE COVER Large $9.15 Water Heater Mounting Kit The 2-tab mounting kit allows you to mount a Dinosaur Electronic's UIB S or UIB S Post ignitor board in an Atwood ® water heater without having to drill a hole to mount the board and risk drilling a hole in the water tank. It comes with an aluminum adapter plate, a clear small cover to protect the UIB S or UIB S Post ignitor board and mounting hardware. 5-59721 2TAB 2-Tab Mounting Kit $27.49 Time Delay Relay Time delay relay is for use in older furnaces that use a standard 12VDC time delay relay. Has a 4 second delay before applying power to the fan motor, and a 2 minute cool down period at the end of the heat cycle before removing power from the fan motor. Will not operate with 110v furnaces. Specs: • 12 VDC operation • Microcontrolled • 4 second delay • 2 minute cool • down cycle • Size: 1.5" x 1.5" • Potted**NOT FOR 110VAC FURNACES.** 5-54800 48000 Time Delay Relay Switch $52.49 DSI w/110V Combo Board Combo DSI board with the 110v pins for water heaters using the pin style connections. Can also be used without the pin connections as a standard 12v DC DSI board. 5-59037 UIB 64 Combo Igniton Board $188.49